0,2mm Frosted PVC Sheet ye dumunifɛnw foroko ye

0,2mm Frosted PVC Sheet ye dumunifɛnw foroko ye

HSQY 0,2mm frosted rigid PVC sheet dabɔra ka kɛ pakew ye minnu dilannen don ni funteni ye, pakew yɔrɔw jɛlenw ni minnu bɛ yeelen bɔ, kɛsu folilenw ani pakew baara wɛrɛw kama minnu bɛ kɛ ni yɔrɔ ye min bɛ kɛ ni nɛnɛ ye walima min bɛ kɛ ni nɛnɛ ye sanni ka kɛ finimugu ye min bɛ kɛnɛya kosɛbɛ.

Fɛn min bɛ kɛ ni nɛnɛ ye, o bɛ yecogo nɔgɔya, a bɛ dɔ bɔ yeelen tilennen na ani ka dɛmɛ don walasa bolokɔniw ni yɔrɔ taamasiɲɛ misɛnninw kana ye kosɛbɛ ka sɔrɔ ka fɛn dilannenw yecogo yɔrɔ dɔ mara. Kulɛri kalasi minnu bɛ ye, minnu bɛ yeelen bɔ ani minnu sugandira, olu bɛ se ka dilan ka kɛɲɛ ni u foroko dilanni ye min wajibiyalen don.

Nin fura in bɛ ni 0,2mm laɲini janya ye, k’a sɔrɔ PVC pake gɛlɛnw ɲɛfɔli minnu bɛ tali kɛ o la, olu bɛ se ka dilan ka bɔ 0,15mm ɲɔgɔn na ka se milimɛtɛrɛ 1 ma ka kɛɲɛ ni foroko kɛcogo ye, a bonya, a sanfɛla laban ani a baara labanko wajibiyalenw. Bonya ni bonya minnu bɛ kɛ ka kɛɲɛ ni mɔgɔw sago ye, olu bɛ sɔrɔ fɛn caman tigɛlikɛlaw ni pakew dilannikɛlaw fɛ.

Ni dumuni bɛ tali kɛ ɲɔgɔn na cogo tilennen na walima ni a ma kɛ cogo tilennen na, PVC dilanni tigitigi ni a dɛmɛni sɛbɛnw ka kan ka dafa ka kɛɲɛ ni dumuni pakew ye, ka kɛɲɛ ni dumuni pakew ye, ka kɛɲɛ ni ɲɔgɔn sɔrɔcogo ye ani ka kɛɲɛ ni taayɔrɔ-sɔgɔli wajibiyalenw ye sani u ka baara kɛ ni u ye jago siratigɛ la.

Frosted PVC Sheet Fɛn dilannenw Jaw

0.2mm Frosted PVC sɛbɛn ɲɛnamaw

*Density, tensile strength ani impact values ​​ye reference values ​​ye ka bɔ HSQY rigid PVC family specification kɔnɔ min bɛ yen. Nafa labanw ka kan ka dafa 0,2mm frosted grade tigitigi la sani a ka san.

Frosted PVC Sheet ye mun ye?

PVC sɛbɛn min bɛ kɛ ni nɛnɛ ye, o ye PVC fɛn gɛlɛn ye walima min bɛ kɛ ni fɛn ye min bɛ kɛ ni fɛn ye min bɛ kɛ ni fɛn ye min bɛ kɛ ni fɛn ye min bɛ yeelen bɔ, ka yeelen bɔlen jɛnsɛn ani ka dɔ bɔ PVC sɔgɔlen kɔrɔlen cogoya la min bɛ kɛnɛya kosɛbɛ.

Ka kɛɲɛ ni a sanfɛla cogoya ye ani a kɛcogo ye, a laban bɛ se ka kɛ ka bɔ a matirili nɔgɔman na ani ka kɛ fɛn ye min bɛ yeelen bɔ ka taa a bila a ɲɛda cogoya la min bɛ ye ka ɲɛ. O b’a to pakew dilannikɛlaw bɛ se ka fɛn dilannenw yecogo yɔrɔ dɔ fara ɲɔgɔn kan ni yɔrɔ jiracogo nɔgɔlen ye.

Ni a bɛ kɛ pakew dilanni na, o fɛn bɛ se ka dilan ni a janya, a bonya ani a ɲɛda cogoya sugandilen ye, ka tila ka wuli ni thermoforming, vacuum forming, cutting, folding walima fɛɛrɛ wɛrɛw ye minnu bɛ bɛn ɲɔgɔn ma.

Nafa minnu bɛ sɔrɔ PVC Surface Frosted walima Matte la

• Reduced Direct Glare: Frosted surface bɛ kɛ cogo ye min ka nɔgɔn ka tɛmɛ PVC transparent kɔrɔlen kan min bɛ kɛnɛya kosɛbɛ.

• Fɛn dilannenw yecogo kɔrɔsilen: Grasi minnu bɛ ye walima minnu bɛ yeelen bɔ, olu bɛ se ka yecogo yɔrɔ dɔ mara ka sɔrɔ ka dɔ bɔ PVC polisilen ɲɛda jɛlen dafalen na.

• Bololabaarakɛminɛnw yecogo duguma: Fɛnɲɛnɛma minnu bɛ kɛ ni matiri ye, olu bɛ se ka bolokɔniw ni yɔrɔ taamasiɲɛ misɛnninw kɛ fɛn ye min tɛ ye kosɛbɛ u minɛtuma na.

• Forokow cogoya: Fɛn minnu bɛ kɛ ni nɛnɛ ye, olu bɛ ɲɛfɔli kɛcogo yecogo ni magacogo danfaralen di feerekɛyɔrɔw foroko dilanni na.

• Seko ni dɔnko ye min bɛ kɛ ni funteni ye: Karamɔgɔ bɛnnenw bɛ se ka sumaya ka kɛ pakew kɔnɔfɛnw ye minɛnw kan minnu bɛ bɛn ɲɔgɔn ma.

• Surface Sugandili minnu bɛ kɛ ka kɛɲɛ ni mɔgɔw sago ye: Matte/matte, matte/glossy walima textured combinations wɛrɛw bɛ se ka jateminɛ ka kɛɲɛ ni a cogoya wajibiyalen ye.

• Ladamuni hakɛw: A janya, a sɛbɛnfura bonya, a bonya ani a kulɛri bɛ se ka bɛn fɛn caman tigɛli ni a foroko wajibiyalenw ma.

Baarakɛcogo suganditaw i n’a fɔ anti-static, UV stabilisation, tasuma baarakɛcogo, dumuni ni dumunikɛminɛnw furakɛli walima sɛbɛnni kɛrɛnkɛrɛnnenw furakɛli, olu bɛ taabolo kɛrɛnkɛrɛnnenw de wajibiya, wa u ka kan ka don fɛn dilannenw ɲɛfɔli sɛbɛn kɔnɔ min dabɔra.

0,2mm PVC ka kɛ Pake thermoformé ye

Ni a janya bɛ se milimɛtɛrɛ 0,2 ma, PVC gɛlɛn bɛnnen don pake nɔgɔlen sugandilenw ma, yɔrɔ minnu na, a ka kan ka kɛ ni foroko dilannikɛlan ye min ka fin kosɛbɛ. A bɛnnenya lakika bɛ bɔ cavity geometry, draw ratio, package stiffness, forming temperature, machine settings ani finished-package performance requirements.

Ni dingɛ jugumanw don walima pake minnu bɛ gɛlɛya caman wajibiya, fɛn dɔ bɛ se ka kɛ min ka bon. Sannikɛlaw ka kan ka pake dafalenw hakɛw ni foroko juguya di ni u bɛ fɛnw ladilikanw ɲini.

Dumunifɛnw foroko dilanni baarakɛcogo

Produce Packaging (Bɔ̀rɔbalenw) Kɛ

Dumuni ni ɲɔgɔn cɛ hakɛ bɛnnenw bɛ se ka jateminɛ sɛnɛfɛnw foroko kɔnɔ minnu dilannen don ni funteni ye, yɔrɔ minnu na foroko dilanni bɛ kɛ ni jɔli gɛlɛn ye ani ka kɛ i n’a fɔ i n’a fɔ nɛnɛ walima nɛnɛ.

Bakery ani Confectionery Pakɛw

PVC min bɛ kɛ ni nɛnɛ ye, o bɛ se ka kɛ burufefeerelaw, fɛnɲɛnamafagalanw, fɛnw doncogo ani jiracogo-pakew kɛcogo sugandilenw na, dumuni ni ɲɔgɔn cɛ wajibiyalenw ni fɛn min bɛ foroko kɔnɔ, o funteni cogoyaw dafalen kɔfɛ.

Sani ani Inserts thermoformés

PVC suguya gɛlɛn minnu bɛnnen don, olu bɛ se ka dilan ka kɛ sanubɔlanw ye minnu man dun, fɛnw dontaw ani pakew kɔnɔfɛn wɛrɛw. A janya ka kan ka sugandi ka kɛɲɛ ni kɔnɔna juguya, a gɛlɛya ani a minɛcogo wajibiyalenw ye.

Box folilenw ani pakew finɛtiriw

PVC matɛri walima min bɛ kɛ ni nɛnɛ ye, o fana bɛ se ka kɛ kɛsu dabɔlenw ye, pakew finɛtiri jɛlenw ani pakew yɔrɔw masirilenw ye yɔrɔ minnu na, a ɲɛda cogoya ka fisa.

Dumuni-ɲɔgɔn-ɲini wajibiyalenw

PVC suguya gɛlɛn walima nɛnɛma bɛɛ man kan ka jate a yɛrɛma i n’a fɔ a bɛnnen don dumuni na. Dumuni ni ɲɔgɔn cɛ bɛnnen bɛ bɔ a dilanni dafalen na, a faralenw, dumuni pakew kɔnɔ, a magali waati, a magali funteni ani a taayɔrɔ sugu ka ɲininiw.

Dumunifɛnw foroko porozɛw kama, aw bɛ dumuni suguya laɲininen di, a kɛra fɛn ye min bɛ se ka ɲɔgɔn sɔrɔ, a kɛra fɛn ye min bɛ se ka kɛ, a kɛra fɛn ye min bɛ se ka kɛ, a marayɔrɔ funteni makɔnɔnen, a sɔrɔ waati ani sariyasɛbɛn minnu wajibiyalen don, ni aw bɛ quotation ɲini.

Seereyaw, fɔtaw walima sɛgɛsɛgɛli rapɔɔri minnu bɛ sɔrɔ, olu ka kan ka sɛgɛsɛgɛ ka kɛɲɛ ni PVC furakisɛ 0,2mm sɔgɔlen tigitigi ye min bɛ di sanni ka kɛ PVC fɛn bɛɛ la caman na.

PVC Frosted (PVC frosted) jiracogo i ka pakew labɛncogo la

Walasa ka kunnafoni sɛbɛncogo ni a fɔcogo bɛnnen labɛn, aw bɛ nin kunnafoniw di:

• A janya wajibiyalen don, i n’a fɔ 0,2mm

• Sɛbɛn walima rollo bonya wajibiyalen don

• Sheet janya walima roll dimensions

• Mate/matte, matte/glossy walima yɔrɔ wɛrɛ wajibiyalen

• Kulɛri min bɛ ye, min bɛ yeelen bɔ, min bɛ fin walima min bɛ kɛ ka kɛɲɛ ni mɔgɔw sago ye

• Thermoforming, vacuum forming, foli walima sɛbɛnni kɛcogo

• Pake hakɛw dafalenw

• Foromasiyɔn jugumanba

• Fɛn min bɛ kɛ pake kɔnɔ

• Dumuni ni ɲɔgɔn cɛ cogoya tilennenw walima cogo tilennen tɛ ni o bɛ se ka kɛ

• Sɛbɛn minnu wajibiyalen don ka ɲɛsin sariya labatoli ma

• Koman hakɛ min bɛ kɛ

• A taayɔrɔ jamana walima kurunbonkarila

Ni thermoforming porozɛ kuraw bɛ kɛ, a ka ɲi ka PVC sugandilenw kɔrɔbɔ masin ni mɔli laɲininen kan sani a ka kɛ jago siratigɛ la. Foroko kelen-kelen, a sanfɛla cogoya, a kɔnɔna ɲɛfɔli, a foroko gɛlɛya ani a datugucogo fɛn o fɛn ka kan ka sɛgɛsɛgɛ kɔrɔbɔli senfɛ.

Tekniki Sɛbɛnw

Nin PVC sɛbɛn minnu bɛ yen, olu bɛ sɔrɔ ka lajɛ. Aw ye a jira ko sɛbɛn bɛ tali kɛ fɛnw hakɛ tigitigi la min bɛ san.

PVC Clear Sheet Kunnafoni sɛbɛn

PVC Rigid Sheet ka tasuma

PVC Gris Board sɛgɛsɛgɛli rapɔɔri

PVC Clear Film kunnafonisɛbɛn

PVC sɛbɛnw sɛgɛsɛgɛli rapɔɔri

20mm Gris Board Test Rapport

PVC sɛbɛn min bɛ kɛ ka Offset sɛbɛnni sɛgɛsɛgɛli rapɔɔri kɛ

Aplikasi Jaw

Foroko ni fɛnw lasecogo

• Misaliw foroko: PVC misali gɛlɛnw hakɛ A4 bɛ se ka kɛ bɔrɔw ni kartɔnw kɔnɔ minnu bɛ u tanga.

• Kurukuruw foroko : Kilo 50 ɲɔgɔn kurukuru kelen na, kurukuruw sɔrɔli bɛ kɛ yɔrɔ min na, walima ka kɛɲɛ ni kiliyanw ka ɲininiw ye.

• Palɛti foroko : Kilo 500–2000 ɲɔgɔn plywood palɛti kelen na ka kɛɲɛ ni fɛnw hakɛ ye ani pakew cogoya ye.

• Konteyna doni : A bɛ se tɔni 20 ma doni tali cogoya la, ka kɛɲɛ ni rollo walima sheet hakɛw ye ani pake laban cogoya ye.

• Lasecogo sariyaw: EXW, FOB, CNF ani DDU.

• Waati min bɛ kɛ ka caya: Tile 10–14 ɲɔgɔn wari bilalen kɔfɛ, ka kɛɲɛ ni fɛn ɲɛfɔlenw ni komandi hakɛ ye.

Sɛbɛnw ni jogoɲumanya sɛbɛnw

Sɛbɛn minnu bɛ sɔrɔ ani sɛgɛsɛgɛli sɛbɛnw ka kan ka bɛn PVC hakɛ tigitigi ma min bɛ kɛ ni nɛnɛ ye. Ni aw ka poroze bɛ dumuniko, fɛn dantigɛlenw walima sɛbɛn kɛrɛnkɛrɛnnen wɛrɛw de wajibiya, aw bɛ sariya wajibiyalen don aw ka ɲininkali la.

Duniya bɛɛ ka ɲɛjiraliw

HSQY Plastic Group bɛ a sen don diɲɛ ɲɛjiraliw la walasa ka pake dilannikɛlaw, thermoforming tɔnw, feerekɛlaw, plastiki fɛn caman tigɛlikɛlaw ani sannikɛla ŋana wɛrɛw kunbɛn.

Ɲininkali minnu bɛ kɛ tuma caman na 0,2mm Frosted PVC Sheet kan

Danfara jumɛn bɛ PVC frosted ni PVC jɛlen jɛlen cɛ?

PVC min bɛ manamana, o ɲɛda bɛ yeelen bɔ ka ɲɛ ani a bɛ yecogo jɛlen di a ma. PVC frosted bɛ baara kɛ ni yɔrɔ matte walima textured ye walasa ka reflections diffuse ani ka translucent yecogo nɔgɔman dilan.

Yala 0,2mm PVC bɛnnen don thermoforming ma wa?

PVC 0,2mm gɛlɛn hakɛ bɛnnen bɛ se ka kɛ thermoformed ye walasa ka pake nɔgɔlen sugandilenw kɛ. A laban bɛnnenya bɛ bɔ dingɛ dunuya la, mɔbili dilanni, foroko funteni, masinw sigicogo ani pakew gɛlɛya wajibiyalen.

Yala PVC min bɛ kɛ ni nɛnɛ ye, o bɛnnen don dumuni ma wa?

Dumuni ni ɲɔgɔn cɛ bɛnnen don, o bɛ bɔ a furakɛcogo tigitigi la ani a kɛcogo laɲininen na. Aw bɛ dumuni suguya, a sɔrɔcogo funteni, a sɔrɔ waati ani a taayɔrɔ-sugu wajibiyalen di walasa ka jate bɛnnen ni sɛbɛnw sɔrɔ minnu bɛ sɔrɔ, olu ka se ka jateminɛ.

Fɛnɲɛnɛma jumɛnw bɛ sɔrɔ?

Nin fura in sinsinnen bɛ PVC 0,2mm frosted kan. PVC gɛlɛnw sɛgɛsɛgɛli minnu bɛ tali kɛ pakew la, olu bɛ se ka dilan ka bɔ milimɛtɛrɛ 0,15 na ka se milimɛtɛrɛ 1 ma, ka kɛɲɛ ni yɔrɔ, bonya ani baarakɛcogo wajibiyalen ye.

Yala ne bɛ se ka matte sugandi fan kelen fɛ ka glossy sugandi fan wɛrɛ fɛ wa?

Mate/matte, matte/glossy ani yɔrɔ wɛrɛw faralen ɲɔgɔn kan, olu bɛ se ka baro kɛ ka kɛɲɛ ni a janya wajibiyalen ye, a dilanni seko ani a komandi hakɛ.

Yala PVC sɛbɛn bɛ se ka kɛ ka kɛɲɛ ni a kulɛri ye wa?

Awɔ. Kulɛri minnu bɛ ye, minnu bɛ yeelen bɔ, minnu bɛ fin ani minnu sugandira ka kɛɲɛ ni u bonya ye, u sanfɛla dafalen ani u komandi hakɛ.

A bonya hakɛ min bɛ se ka sɔrɔ, o ye mun ye?

PVC sɛgɛsɛgɛli gɛlɛn min bɛ yen, o bɛ a jira ko a bonya hakɛ maksimali bɛ se milimɛtɛrɛ 1280 ma. Bonya laban min bɛ sɔrɔ, o ka kan ka dafa 0,2mm frosted grade sugandilen na.

Yala PVC frosted bɛ se ka sɛbɛn wa?

PVC hakɛ bɛnnenw bɛ se ka kɛ ni sɛbɛnni kɛcogo ye min bɛ bɛn. Encre system, surface energy, matte texture ani adhesion wajibiyalen ka kan ka jateminɛ sani a ka kɛ caman ye.

Yala ne bɛ se ka misali ɲini sani ka komandi kɛ wa?

Baro bɛ se ka kɛ misali fɛnw kan ka kɛɲɛ ni u janya ye min bɛ sɔrɔ, u sanfɛla labɛncogo ani u kulɛri. Ni poroze minnu bɛ kɛ ni funteni ye, a ka ɲi ka sɛgɛsɛgɛli kɛ sɛnɛfɛnw dilanni minɛn laɲininenw kan sani a ka kɛ caman ye.

Koman hakɛ fitinin ye mun ye?

MOQ min bɛ sɛbɛn sisan, o ye kilo 1000 ye. Kulɛri minnu bɛ kɛ ka kɛɲɛ ni mɔgɔw sago ye, u ɲɛda cogoya walima u hakɛ kɛrɛnkɛrɛnnenw bɛ se ka kɛ sababu ye ka fɛn dilanni hakɛ fitininw kɛ minnu tɛ kelen ye.

Ne ka kan ka kunnafoni jumɛnw di walasa ka quotation sɔrɔ?

Aw bɛ a janya, a bonya walima a sɛbɛn hakɛ, a yɔrɔ faralen ɲɔgɔn kan, a kulɛri, a dilanni walima a sɛbɛnni kɛcogo, a foroko hakɛ dafalenw, dumuni ni ɲɔgɔn cɛ wajibiyalenw ni a bɛ se ka kɛ, a hakɛ ani a taayɔrɔ di.

HSQY Plastic Group ko la

HSQY Plastic Group bɛ PVC sɛbɛn gɛlɛnw ni filimu dilan walasa ka thermoforming, pakew, sɛbɛnni, kɛsu foli ani izini fɛn caman tigɛli. Fɛn minnu bɛ sɔrɔ, olu ye PVC suguya jɛlenw ye, minnu ɲɛw ye ɲɛgɛn ye, minnu ɲɛw ye ɲɛgɛn ye, minnu bɛ kɛ ni nɛnɛ ye ani minnu bɛ kɛ ka kɛɲɛ ni u kɛcogo kɛrɛnkɛrɛnnenw ye, minnu bɛ kɛ fɛn dilannikɛlaw, fɛn caman tigɛlikɛlaw ani feerekɛlaw ye.

Ka ɲɛsin PVC foroko dilanni porozɛw ma minnu bɛ kɛ ni nɛnɛ ye, HSQY bɛ se ka baro kɛ a bonya, a bonya, a sɛbɛnfura walima a wulicogo hakɛw kan, a ɲɛda matɛrilenw faralen ɲɔgɔn kan, a kulɛri, a dilanni wajibiyalenw, a misaliw, a kɛcogo sɛbɛnw, a pakew dilanni ani a caman sɔrɔli ka kɛɲɛ ni kiliyan ka ɲinini ye.